RollerDrive EC200

RollerDrive EC200 is equipped with an integral motor control which fulfills all required commutation- and safety functions. Independent from load on the conveyor, EC200 runs always with the same speed featuring a true four-quadrant- motion controller.
EC200 can be used with out any external control electronic. By using a combined analog Signal (0 -10V), speed and start is set. This input is valid up to 28 V, which makes it very easy to control the EC200 with a simple relay, so that it runs at full speed.
There is also a compact interface box available, to simplify the speed setting and decouple the signals.


RollerDrive HPBL

Characteristics
  • 25 Watts continuous mechanical performance
  • Integral commutation electronic
  • Constant conveyor speed
  • After run reducing motor stop function
  • 15.000 hours minimum operation time
  • Protection rate IP54 or IP66
  • 55 dB(A) noise emission mounted in conveyor
  • 450 mm cable length
  • 5 pole Fixcon connector


User Manual Interroll RollerDrive EC200

EC200 Electrical Data
Nominal voltage 24 VDC
Voltage range 18 - 28 VDC
No load current 0.4 A
Maximum continuous current
 2.1 A
Maximum peak current 5.5 A
Mechanical Performance 25 W
Maximum ripple from power supply 3%
Noise emission (mounted) 55 dB(A)
Lifetime under nominal conditions 15000 h
System Efficiency (Drive)
 49 %

EC200 Speed/Load Performance Data

Gear Ratio Nominal Speed
m/s
 Nominal Torque
Nm
 Peak Torque
Nm
12 0.98-0.14
 0.7
 1.2
16
 0.74-0.11 0.9
 1.8
36
 0.33-0.05
 1.7
 3.6
48
 0.25-0.04
 2.3
 5.4
64
 0.18-0.03
 3.6
 8

Minimum RL

CartridgeTubeIdler bearingMin RL
12:1 to 16:1 No groove 11 mm hexagonal end drilled and tapped M8 266
No groove 11 mm hexagonal spring loaded 309
No groove PolyVee end drilled and tapped M8 291
No groove PolyVee 11 mm hexagonal spring loaded 302
No groove Timing belt/3/8" chain end drilled and tapped 283
Groove 30 60 11 mm hexagonal end drilled and tapped M8 309
Groove 50 80 11 mm hexagonal spring loaded 325
36:1 to 48:1 No groove 11 mm hexagonal end drilled and tapped M8 256
No groove 11 mm hexagonal spring loaded 299
No groove PolyVee end drilled and tapped M8 281
No groove PolyVee 11 mm hexagonal spring loaded 292
No groove Timing belt/3/8" chain end drilled and tapped 273
Groove 30 60 11 mm hexagonal end drilled and tapped M8 299
Groove 50 80 11 mm hexagonal spring loaded 315
12:1 to 16:1 No groove 11 mm hexagonal end drilled and tapped M8 262
IP66 version Groove 30 60 11 mm hexagonal end drilled and tapped M8 305
36:1 to 48:1 No groove 11 mm hexagonal end drilled and tapped M8 250
IP66 version Groove 30 60 11 mm hexagonal end drilled and tapped M8 293
The minimum RL is determinate by the idler bearing and grooves. Maximum RL: 1500 mm.

DriveControl for EC200 RollerDrives
DC-EC200/300
                                
top
© Interroll | Disclaimer